C-BIOS is an open source BIOS for MSX computers. It can be booted either on BIOS or UEFI (including Intel-MAC). Besides i386 it also includes a 64bit Linux kernel generating the possibility to chroot into a 64bit (amd64) userspace environment. The system can serve as a full rescue / backup / restore system for Linux or Windows based. Free ASUS K45A drivers for Mac OS X. Select driver to download.
- Mac Os Bios Key
- Bios Asus For Mac Os High Sierra
- Bios Asus For Mac Os Catalina
- Bios Asus For Mac Os 10.13
- Introduction Essentially, the BIOS (or UEFI) is the settings page for your computer's motherboard. From here, you can fiddle with how your computer hardware works- it's often necessary to change a few basic settings in the BIOS or UEFI to get Mac OS X up and running.
- If your PC has a Gigabyte motherboard with BIOS, follow this guide. Choose the hard drive you want to install macOS on and click the Erase tab. Make sure Mac OS Extended (Journaled) is.
- The Basic Input/Output System (BIOS) is a very important software that loads the currently installed OS, and tests all of the system's hardware components – so make sure you flash it correctly.
NOTE: This guide primarily applies to the UEFI on older Gigabyte motherboards with the LGA 1155 socket-- this means P67, Z68, Z77, H67, H77, B75, and Q77 motherboards. If you use a newer motherboard with the LGA 1150 socket, ignore the sections on xHCI and EHCI.
Introduction
Essentially, the BIOS (or UEFI) is the settings page for your computer's motherboard. From here, you can fiddle with how your computer hardware works-- it's often necessary to change a few basic settings in the BIOS or UEFI to get Mac OS X up and running. The BIOS standard is generally used by motherboards from before 2012, while the UEFI standard is used by motherboards made after that.
UEFI on the left, BIOS on the right |
Guide
To enter the UEFI on a Gigabyte motherboard, press the delete key when your computer boots (before the operating system starts). Different manufacturers set different keys for opening the UEFI. On some Gigabyte motherboards, this will bring you to the '3D BIOS'. From here, you can choose which specific part of your motherboard that you want to manage.
However, the 3D BIOS is kind of annoying to use. Instead, click on the 'Advanced' section in your UEFI instead (UEFI allows you to use your mouse cursor). This will lead you to a more standard-looking settings page.
Before starting, it's best just to reset all of your UEFI settings to their factory defaults. On Gigabyte motherboards, you can reset your UEFI settings to their default by pressing the 'F7' key. Once your UEFI is running on its defaults, you will have to change the following settings:
Boot Option Priorities - Change 'Boot Option #1' to your USB drive. You need to do this for Unibeast to work. After you finish installing Mac OS X, you should change this setting back to default, so your main hard disk is the first boot option (this optional, but it will speed up your boot times later on).
On Gigabyte motherboards, the settings page will often show you two versions of each hard disk: the UEFI version (usually labeled as 'UEFI'), and the legacy version (usually labeled as 'P', 'SATA,' or 'Legacy'). If you installed OS X El Capitan through the Unibeast method, you must set the UEFI version as first priority. This is because Hackintoshes with El Capitan use the Clover bootloader, which only works with UEFI boot.
However, if you are installing an older version of OS X through the Unibeast method (e.g. Yosemite, Mavericks, etc.), you must select the
Mac Os Bios Key
legacy version as first priority. This is because Hackintoshes with older versions of OS X usually use Chameleon or Chimera bootloader, which does not support UEFI boot.Bios Asus For Mac Os High Sierra
Bios Asus For Mac Os Catalina
xHCI Mode - Change this to 'Auto'. This setting is usually set to 'Smart Auto', which doesn't work.Bios Asus For Mac Os 10.13
xHCI Hand-off / EHCI Hand-off - Make sure both of these settings are enabled.
Even though the UEFI supports using a mouse, it'll probably be easier to navigate through the UEFI with the arrow keys on your keyboard. Press 'Enter' to change a selected option in the UEFI. On a Gigabyte motherboard, press F10 to save my changes.